search

Marathon 1100 SL Instructions d'exploitation Page 10

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 35
  • Table des matières
  • MARQUE LIVRES
    • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 9
Assembly
9
• Mark points 74 mm to right and left of the centre of door (VM), and at
same height on lintel or ceiling (see Fig. 8).
Wear safety goggles when drilling!
Check thickness of ceiling, particularly in the case of prefabri-
cated garages!
• Drill two holes (Ø 10 x 65 mm).
• Open door. Transfer door centre mark (HM) to ceiling.
Close door.
• Insert plug (1). Lift up operator (2) at front. Secure lintel fitting (3) at
the front with two screws (4) and plain washers (5).
Protect control unit housing (6) from damage!
Attention !!
Always install operator parallel to the guide rails of the door.
• Lift up operator.
• Align ceiling bracket (1). It should be located within a range of
(R = 0 ...600 mm).
Use a non-slip, stable stepladder!
13
HM
14
B
600
0
1
1
HM
3
2
5
4
13
12
2
6
S10
4
5
31
12
11
10
VM
74mm 74mm
10mm
65mm
HM
10 11
• Align operator mechanism horizontally to rear centre of door (HM).
Mark position of holes.
Wear safety goggles when drilling!
Check thickness of ceiling, particularly in the case of prefabri-
cated garages!
• Drill two holes (Ø 10 x 65 mm).
• Insert plug (1). Fit two screws (2) with plain washers (3). Tighten
screws (2) securely.
• Align C-rail (4) at correct height. If necessary, move screws (5).
Tighten screws (5).
• Mount connecting rod (1):
Introduce bolt (2) and attach the retainer (3).
• Mount door fitting (4)
insert bolt (5) and attach retainer (3).
• Pull once on the emergency release cord (N). This unlocks the trolley
(1). Tighten screw (8) on lintel fitting.
• Use connecting rod (2) to push trolley (1) as far forward as possible
(3). If necessary, release switch-trigger (4).
• Align angle of door fitting with centre of door (VM) and mark 5 drill
holes. Drill 5 holes (Ø 5 mm).
Wear safety goggles when drilling!
Use screws that are suitable for the door material.
• Insert 5 hexagon-head screws (6) and tighten securely.
• Release switch-trigger (4) and push right up to trolley (7).
• Tighten switch-trigger buffer screw (4) securely.
Trim (e.g. saw off and debur) projecting part of ceiling bracket (4).
• Release rear switch-trigger buffer (1) and push right back to stop (2).
Open door (3) by hand.
• Push switch-trigger (1) right up to trolley (5). Securely tighten screw
on switch-trigger (1).
17
4
7
N
1
8
2
6
max. 30°
4
5
3
17
16
15
15
2
3
5
4
3
1
2
48
7
3
6
5
1
N
VM
16
14
Vue de la page 9
1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 34 35

Commentaires sur ces manuels

Pas de commentaire
Produits connexes et manuels pour Ouvreur de porte de garage Marathon 1100 SL
Ouvreur de porte de garage Marathon 1100 SL Instructions d'exploitation   (37 pages)
Ouvreur de porte de garage Marathon 1100 SL Instructions d'exploitation   (21 pages)
  • DR Prop Redman Power Chair Vogt Hanna Instruments Camos
  • ALLEN & HEATH Équipement musical Shoprider Non Archos Téléviseurs et moniteurs Muratec Multifonctionnels Tripp Lite Docks d'ordinateurs portables et duplicateurs de ports
  • Acer TravelMate 8200 Electrolux EWF1290ED Frigidaire FFSS2314QE Uniwell NX-5400 Perreaux PMF1050
  • Craftsman 4-Drawer Manuel de service KitchenAid KHSP5 86510 Mode d'emploi Sharp UX-460 Manuel de l'utilisateur Samsung MD230X6 Manuel de l'utilisateur Samsung MX-H630 Manuel de l'utilisateur